SRM GASのStepperMotorが使えない Nakagaki-san, Ikeda 概要: K-Log#34519:Offload of F1 GASに関連した作業です。 SRMのVISミニラックにあるネットワークSWが通信異常により、SRM GASのStepperMotorと通信できなくなっていた。 その為、SRMのネットワークスイッチをPoE給電しているOMC側のLANケーブルの抜き差しで再起動して回復させました。 詳細: R.Takahashi-sanからSRM GASのStepperMotorが使えないと連絡を受けた。 調査したところ、Stepperモーターのリレーは僅かに反応があった。 k1script1からLANシリアル変換へのPingは応答がない k1script1からSRMのVISミニラックのネットワークSWの応答あり しかし、ネットワークSWのWEB IFの応答がない そのため、SRMのネットワークSWの通信異常が発生していると推測した。 SRMのネットワークSWはPoE給電を使っているので、OMCの給電側でON/OFFを制御できる。 しかし、ポート一覧が見つからなかった。 その為、コントロールルームで相談して入坑することにした。 14:13 センターへ入り、OMCネットワークスイッチからSRMのLANケーブルを抜き差しした 14:15 その後、BS付近のWSにてSRM GASのBIOとスクリプトからONにできることを確認 14:18 高橋さんへ引き渡した 14:19 中央から出ました OMCのNetwork SWのPort --- Pico Network 01: PD mini rack sw 02: OMC mini rack sw 03: SR3 mini rack sw 04: SR2 mini rack sw 05: SRM mini rack sw 06: BS mini rack sw 07: PR2 mini rack sw 08: Green X Table sw 09: Green Y Table sw 10: AS Table sw 11: Precision Air Processer SRX1 12: AS_WFS HWP --- DGS Network --- 18: OMC WS --- SRM GAS Stepper Motor Unavailable [Nakagaki-san, Ikeda] Summary: This work is related to K-Log#34519: Offload of F1 GAS. https://klog.icrr.u-tokyo.ac.jp/osl/?r=34519 Due to a communication failure with the network switch located in the SRM VIS mini-rack, communication with the SRM GAS Stepper Motor was lost. To recover, we restarted the SRM network switch by unplugging and reconnecting the LAN cable on the OMC side, which supplies PoE to the switch. Details: We received a report from R. Takahashi-san that the SRM GAS Stepper Motor was not functioning. Upon investigation, we found the following: The relay of the Stepper Motor showed slight response. There was no ping response from k1script1 to the LAN-serial converter. The SRM VIS mini-rack network switch did respond to pings from k1script1. However, the web interface of the network switch was unresponsive. Based on this, we suspected a communication failure within the SRM network switch. Since the SRM network switch uses PoE, its power can be controlled from the OMC side. However, we were unable to locate the port list for remote control. Therefore, after consulting in the control room, we decided to enter the tunnel for manual intervention. 14:13 - Entered the center and reconnected the LAN cable from the OMC network switch to the SRM. 14:15 - Confirmed at the BS area workstation that the SRM GAS Stepper Motor could be turned ON via BIO and scripts. 14:18 - Handed over control to Takahashi-san. 14:19 - Exited the central area. OMC Network Switch Port Assignments: Pico Network 01: PD mini rack switch 02: OMC mini rack switch 03: SR3 mini rack switch 04: SR2 mini rack switch 05: SRM mini rack switch 06: BS mini rack switch 07: PR2 mini rack switch 08: Green X Table switch 09: Green Y Table switch 10: AS Table switch 11: Precision Air Processor SRX1 12: AS_WFS HWP DGS Network 18: OMC Workstation