YamaT-san, DanChen-san, Ushiba-san, Ikeda

概要
Work related to K-Log#33152 : Installation of Coil Driver Switcher
https://klog.icrr.u-tokyo.ac.jp/osl/?r=33152

Low Power Coil DriverのBIO接続の為、k1ex1のモデル変更を行った。
6枚目のDIO6464カードを入れると全てのカードが認識できなかったとのYamaT-san達からの報告により、既存のBIO接続を変更した。

変更内容

BIO接続変更内容
変更前:
 k1visetmxlsc
  IMB: H32_C3
  TP: L32_C4
 k1visetmxt
  PI: L32_C0

変更後:
 k1visetmxlsc
  IMB: remove
  TP (LPCD): H32_C3 (IMBから移動) <- コイルドライバごとIMBのを再利用しているので配線はIMBのまま使う
  CoilDriver_SW: L32_C0 (PIから移動)
  TM_HP: L32_C4 (TPから移動)
 k1visetmxt
  PI: H32_C4(BO:Release_SensorのBO側は未使用の為、これを使用する, BI:remove)

モデル変更箇所
PAYLOAD_MASTER/
  次のブロックを新規追加
　CRYO_PAYLOAD_16K_HP_MASTER
　　CRYO_PAYLOAD_16K_MASTERからコピーしてBIO,TMブロックを変更
  PAYLOAD_OPLEV_HP_TYPE_A_16K
    PAYLOAD_OPLEV_TYPE_A_16KからコピーしてMASTERを変更。COILOUTF_HPを追加
  PAYLOADMASTER_HP
  PAYLOADBIO_HP
  A_PAYLOADBIO_HP_ENCODE  
  A_PAYLOADBIO_HP_DECODE
   オリジナルをコピーしてHP関連を追加

　CRYO_PAYLOAD_16K_HP_MASTER
  新規ブロックに置き換え

k1visetmxt:
  BIO接続の変更のみ

k1visetmxlsc:
  CRYO_PAYLOAD_16K_MASTERからCRYO_PAYLOAD_16K_HP_MASTERへ変更
  BIO接続の変更
  DAC_1 In12-15: TM_{H1,H2,H3,H4}からTM_{H1,H2,H3,H4}_HPへ変更
  DAC_2 In12-15: GNDからTM_{H1,H2,H3,H4}へ変更
  ETMXブロックをCRYO_PAYLOAD_16K_MASTERからCRYO_PAYLOAD_16K_HP_MASTERへ変更

SDFは、TM_COILOUTFからTM_COILOUTF_HPへ名前を変更後、TM_COILOUTFのEPICS値をsafe.snapへ上書きした。
フィルタバンクは、TM_COILOUTFからTM_COILOUTF_HPへコピーした。

---
YamaT-san, DanChen-san, Ushiba-san, Ikeda

Overview
Work related to K-Log#33152 : Installation of Coil Driver Switcher
https://klog.icrr.u-tokyo.ac.jp/osl/?r=33152

The model of k1ex1 was modefied for BIO connection of Low Power Coil Driver.
YamaT-san and others reported that they could not recognize all cards when the sixth DIO6464 card was inserted, so the existing BIO connection was changed.

Details of the change

BIO connection changes
Before change
 k1visetmxlsc
  IMB: H32_C3
  TP: L32_C4
 k1visetmxt
  PI: L32_C0

After change
 k1visetmxlsc
  IMB: remove
  TP (LPCD): H32_C3 (Moved from IMB) <- Reuse the entire coil driver from IMB, so use the wiring as IMB
  CoilDriver_SW: L32_C0 (Move from PI)
  TM_HP: L32_C4 (Move from TP)
 k1visetmxt
  PI: H32_C4 (BO: BO side of Release_Sensor is unused, so use this, BI:remove)

Model change point
PAYLOAD_MASTER/
  Add the following new block
　CRYO_PAYLOAD_16K_HP_MASTER
　　Copy from CRYO_PAYLOAD_16K_MASTER and change BIO,TM block
  PAYLOAD_OPLEV_HP_TYPE_A_16K
    Copy from PAYLOAD_OPLEV_TYPE_A_16K and change MASTER, add COILOUTF_HP
  PAYLOADMASTER_HP
  PAYLOADBIO_HP
  A_PAYLOADBIO_HP_ENCODE  
  A_PAYLOADBIO_HP_DECODE
   Copy the original and add HP-related

　CRYO_PAYLOAD_16K_HP_MASTER
  Replaced with new block

k1visetmxt:
  Only change BIO connection

k1visetmxlsc:
  Changed from CRYO_PAYLOAD_16K_MASTER to CRYO_PAYLOAD_16K_HP_MASTER
  Change of BIO connection
  DAC_1 In12-15: Change from TM_{H1,H2,H3,H4} to TM_{H1,H2,H3,H4}_HP
  DAC_2 In12-15: Change from GND to TM_{H1,H2,H3,H4}
  ETMX block changed from CRYO_PAYLOAD_16K_MASTER to CRYO_PAYLOAD_16K_HP_MASTER

SDF overwrote the EPICS value of TM_COILOUTF to safe.snap after renaming from TM_COILOUTF to TM_COILOUTF_HP.
Filter banks were copied from TM_COILOUTF to TM_COILOUTF_HP.