DGSメンテナンスデー(12/23)の定期確認 Stepperモーター [確認内容] BIOにて電源制御できるか確認 Scriptを開始できるか確認 リミットスイッチインストールされている箇所はGreenになっていることを確認 [確認結果] 問題なし Release Sensor [確認内容] Release Sensorが0であることを確認、1:着座 [確認結果] ETMX, ETMY, ITMX, ITMY : 問題なし Picomotor [確認内容] PingTestを行う [確認結果] 既知のみ NG: MCI,STM1, POP_POM,POS_POM,POM1 MCF(MCO,MCI) => 確認のみ、復旧作業はしませんでした。 OK: ETMX,ETMY,ITMX,ITMY BS(IM,BF),SRM(IM,BF),SR2(IM,BF),SR3(IM,BF,STM) PRM(IM,BF),PR2(IM,BF),PR3(IM,BF) MCE,IMMT1,IMMT2,OMMT1,OMMT2,OSTM REFL_WFS,POP,POP2,POS,POS2,POP_WFS,AS_WFS PCAL(EX1,EX2,EY1,EY2):使用時のみONなので未確認 温度調整機 [確認内容] ・温度取得が正しく動作しているか。 [確認結果] 問題無し 精密空調 [確認内容] ・温度取得が正しく動作しているか。 [確認結果] 問題無し FunctionGenerator (確認内容) ・Ping応答があるか。 ・EPICSチャンネルが全て生きているか。 [sitemap]-[Commissioning]-[ALS FG]-[Xarm],[Yarm] [確認結果] ・X,YのPLLは正常に動作している。 HWP control PC (確認内容) ・制御用PCへのログイン可能かの確認 (確認結果) ・k1hwp0,1,2:OK --- DGS Regular maintenance day(12/23) Stepper motor [Checked] Check if the power supply can be controlled by BIO Check if the script can be started Checked that the limit switches installed are green. [Check result] No problem Release Sensor [Checked the Release Sensor.] Checked that Release Sensor is 0, 1: Seated. [Check result] ETMX, ETMY, ITMX, ITMY : No problem Picomotor [Confirmation] PingTest is performed. [Result] Only known NG: SR2(IM) : Not restored today due to other work priorities MCI,STM1, POP_POM,POS_POM,POM1 MCF(MCO,MCI) => Confirmation only, no recovery operation was performed. OK: ETMX,ETMY,ITMX,ITMY BS(IM,BF),SRM(IM,BF),SR2(IM,BF),SR3(IM,BF,STM) PRM(IM,BF),PR2(IM,BF),PR3(IM,BF) MCE,IMMT1,IMMT2,OMMT1,OMMT2,OSTM REFL_WFS,POP,POP2,POS,POS2,POP_WFS,AS_WFS PCAL(EX1,EX2,EY1,EY2):Not checked because it is ON only when used Temperature controller [Checked] Is the temperature acquisition working properly? [Check result] Is the temperature acquisition working properly? => No problem Precision air Processer [Check Contents] Is the temperature acquisition working properly? [Result] No problem FunctionGenerator (Confirmation) Is there a ping response? Are all EPICS channels alive? [sitemap]-[Commissioning]-[ALS FG]-[Xarm],[Yarm]. [Check result] X and Y PLLs are working properly. HWP control PC (Confirmation) Check if it is possible to login to the control PC. (Result) Both k1hwp0, 1 and 2 are OK.