Model共通化: Type-A(ITMY)をPAYLOAD_MASTERとTOWER_MASTERに対応しました。
http://klog.icrr.u-tokyo.ac.jp/osl/?r=15675
http://klog.icrr.u-tokyo.ac.jp/osl/?r=15641
の作業と同じです。

・ITMYの対応内容
 PAYLOAD_MASTER, TOWER_MASTERに置き換えを行いました。

 ・PAYLOAD,TOWER共にMODALの削除を行った。
 
 ・MODAL削除により、次のSHMEMは使用しない為削除。
  PAYLOAD
  K1:VIS-ITMY_MN_COIL_{V1,V2,V3,H1,H2,H3}
  K1:VIS-ITMY_IM_COIL_{V1,V2,V3,H1,H2,H3}
  K1:VIS-ITMY_TM_COIL_{V1,V2,V3,H1,H2,H3}
  K1:MODALITMY_{OLL,OLP,OLY,MNOLY}
  K1:VISITMYP-VISITMYT_{COM2L,COM2Y} 
  TOWER
  K1VIS-ITMY_IP_COIL_{H1,H2,H3}
  K1VIS-ITMY_BF_COIL_{V1,V2,V3,H1,H2,H3}
  K1:VIS-ITMY_GAS_COIL_{F0,F1,F2,F3,BF}
  K1:VISITMYP-VISITMYT_{COM2L,COM2Y} 

 ・ITMY_IP_ACCMONは削除
 ・Accelerometer Test(remove me after the test)は全て削除
 
 ・TOWERの次の対応は、他のTYPE-Aと同じに合わせました。
  {MN,IM}_OSEM_{V1,V2,V3,H1,H2,H3}
  PF/MN OpLev(K-Log#16185)
  MN_OL_{TILT,LEN,ROL,TRA,VER}_{SEG1,SEG2,SEG3,SEG4}_In
  PF_OL_{TILT,LEN}_{SEG1,SEG2,SEG3,SEG4}_In
  BIO Monitor Input,BIO Control Outputs
  ITMY_BIO_ENCODE、DECODEに置き換え

 ・次のSHMEMを追加しました。
  K1:VIS-ITMYP_ISC_MN_OUT

SDF:
 CHANS NOT FOUND: SDF RESTORE-LOAD
 CHANS NOT INIT: MON(ACCEPT) - CONFIRM 

Foton：
 次の名称変更を行った。
 TOWER
  MOD_*は全て削除
  TEST_ACC_*は全て削除
 PAYLOAD
  MOD_*は全て削除

k1modalitmy:
 /opt/rtcds/kamioka/k1/target/fb/master
  次の２行をコメントアウトしてkillk1modalitmyを行った。
  /opt/rtcds/kamioka/k1/chans/daq/K1MODALITMY.ini
  /opt/rtcds/kamioka/k1/chans/daq/tpchn?k1modalitmy.par

---
Support for common Payload/Tower model files:  Type-A (ITMY) is supported to TOWER_MASTER/PAYLOAD_MASTER.

Model commonization: Type-A (ITMY) is now compatible with PAYLOAD_MASTER and TOWER_MASTER.
http://klog.icrr.u-tokyo.ac.jp/osl/?r=15675
http://klog.icrr.u-tokyo.ac.jp/osl/?r=15641
This is the same as the work of

ITMY support
 PAYLOAD_MASTER and TOWER_MASTER have been replaced.

 The deletion of MODAL was done for both PAYLOAD and TOWER.
 
 By deleting the MODAL, the next SHMEM is deleted because it is not used.
  PAYLOAD
  K1:VIS-ITMY_MN_COIL_{V1,V2,V3,H1,H2,H3}
  K1:VIS-ITMY_IM_COIL_{V1,V2,V3,H1,H2,H3}
  K1:VIS-ITMY_TM_COIL_{V1,V2,V3,H1,H2,H3}
  K1:MODALITMY_{OLL,OLP,OLY,MNOLY}
  K1:VISITMYP-VISITMYT_{COM2L,COM2Y} 
  TOWER
  K1VIS-ITMY_IP_COIL_{H1,H2,H3}
  K1VIS-ITMY_BF_COIL_{V1,V2,V3,H1,H2,H3}
  K1:VIS-ITMY_GAS_COIL_{F0,F1,F2,F3,BF}
  K1:VIS-ITMYP-VISITMYT_{COM2L,COM2Y} 

 Remove ITMY_IP_ACCMON.
 Remove all "Accelerometer Test (remove me after the test)".
 
 The following correspondence of TOWER has been adjusted to be the same as other TYPE-A.
  PF/MN OpLev(PF/MN, IM)
  PF/MN OpLev(K-Log#16185)
  MN_OL_{TILT,LEN,ROL,TRA,VER}_{SEG1,SEG2,SEG3,SEG4}_In
  PF_OL_{TILT,LEN}_{SEG1,SEG2,SEG3,SEG4}_In
  BIO Monitor Inputs, BIO Control Outputs
  Replace with ITMY_BIO_ENCODE and DECODE.

 The following SHMEMs have been added.
  K1:VIS-ITMYP_ISC_MN_OUT

SDF:
 CHANS NOT FOUND: SDF RESTORE-LOAD
 CHANS NOT INIT: MON(ACCEPT) - CONFIRM 

Foton.
 The following name changes were made.
 TOWER
  All MOD_* were deleted.
  Removed all TEST_ACC_*.
 PAYLOAD
  Remove all MOD_*.

k1modalitmy:
 /opt/rtcds/kamioka/k1/target/fb/master
  I commented out the next two lines and did killk1modalitmy.
  /opt/rtcds/kamioka/k1/chans/daq/K1MODALITMY.ini
  /opt/rtcds/kamioka/k1/chans/daq/tpchn?k1modalitmy.par